F0 E2Amana · Washer

Amana Washer F0 E2: Official Meaning and Checks

Routine checkStart with the safe checks below.

Direct answer

What F0 E2 means

Official Amana material describes F0 E2 as The F0 E2 error code means your washer has detected excessive suds in the washer basket. This guide records the cited product-family scope, safety-reviewed owner checks, and service limits.

Before you begin

Safety first

Safety review is complete for the owner-accessible checks shown here. Do not remove panels, bypass controls, or test live circuits.

  • Record the complete displayed code and the full model number before clearing the display.
  • Disconnect power before touching a user-accessible filter, hose, burner, or electrical connection.
  • Stop using the equipment if it leaks, smells burned or of gas, smokes, sparks, or trips a breaker.

Does this guide apply?

Region
United States
Product family
Front Load Washers (URL category: Laundry/Washers/FrontLoadWashers/ErrorCodes/%22F%22ErrorCodes)
Scope note
The cited source scope is Front Load Washers (URL category: Laundry/Washers/FrontLoadWashers/ErrorCodes/%22F%22ErrorCodes). Confirm the complete model number before applying the guidance; an empty model list does not imply all models.

Common paths to check

These are source-backed possibilities, not probability estimates for your specific unit.

  • 01 Official source meaning: The F0 E2 error code means your washer has detected excessive suds in the washer basket.

Decision path

Safe checks, in order

  1. 1

    Confirm code and model scope

    Compare the complete display and full model number with the cited manufacturer page or manual before applying any troubleshooting instruction.

    Expected: The official source explicitly covers the displayed code and product family.

    If not resolved: Contact manufacturer support with the full model and serial number.

  2. 2

    Follow the official owner checks

    The washer will run an automatic suds reduction routine to try to eliminate most of the excess sudsing. Allow the washer to continue to run. Did you use High Efficiency (HE) detergent? Use only High Efficiency (HE) detergent. Using non-HE detergent or more than the manufacturer's recommended amount of soap can cause excessive suds. The excess suds can cause the washer to run at a reduced spin speed, resulting in very wet loads. It can also increase the cycle time due to increased rinses trying to eliminate the suds. If you see "Sud" or "Sd" with the Rinse status light on, the washer is removing suds. Let the cycle continue. If you see "Sud" or "Sd" and the Cycle Complete light is on, the washer detected too many suds during the cycle, and your load may not be thoroughly rinsed, or water may not be entirely removed. You may want to select a Rinse/Spin cycle for further rinsing. Which detergent should you use? Amana recommends using Swash® Laundry Detergent. It is designed to work in both high-efficiency (HE) and non-HE washing machines. With an 8x concentrated formula, you’ll use about a quarter of the detergent you’d need with a traditional 2x concentration detergent. It may look like a small amount, but you’ll be amazed at its effectiveness. Is the bulk dispenser being used? If your washing machine has a bulk dispenser feature, check the following: Is the bulk dispenser enabled? If it is, there is no need to add additional detergent to the load. Doing so could cause…

    Expected: Only the user-accessible condition identified by the official source is corrected.

    If not resolved: Stop repeated resets and arrange qualified service if the code returns or the source directs service.

Reset and test

A user reset is not documented for this condition.

Important: A reset may clear the display but cannot repair the underlying condition; follow only the exact model-specific manufacturer procedure.

Escalation point

Stop and arrange service when

  • The code returns after the cited user-accessible checks or the official source directs professional service.
  • The equipment leaks, smells burned or of gas, smokes, sparks, overheats, or trips a breaker.

Official sources

We paraphrase manufacturer material and show the publication scope so you can verify it.

  1. F0 E2 - Front Load Washer, section: Possible Solutions body Amana · F0 E2 (Front Load Washers); source fingerprint 5bf5682f766d40527307ce25bb8f0704de2e9da48634c0cd7979a758a603cef5 (SHA-256 of page body text) · accessed 2026-08-08

Reviewed by Device Fix Guide · Last source check: